FBO5 Left Hand Machine
FBO5 Right Hand Machine
FBO5 Left one car 20 min of cooling FBO5 Left 30 min of cooling @ 80 mph FBO5 Right 45 min. of cooling @80mph
MOLDING MACHINE SPECIFICATIONS:
FBO-V, 2430; 9-12/9-12, Nominal 90 MPH
FBO-V, 3032; 11-14/11-14, Nominal 80 MPH
FBO-V, 3232; 9-12/9-12, Nominal 80 MPH
FBO-V, 3232; 11-14/11-14, Nominal 80 MPH
Mold dimensions (nominal)
Operator selectable cope and drag heights
Standard settings
24" x 30" (610mm x 762mm);
9" to 12" (229mm to 305mm)
Low 9", mid 10.5", high 12"
30" x 32" (762mm x 810mm);
11" to 14" (279mm to 356mm)
Low 11", mid 12-1/2", high 14"
32" x 32" (810mm x 810mm);
Low 11", mid 12.5", high 14"
Method of operation
Fully automatic or; Stops for core insertion
Fully automatic, or, Stops for core insertion
Touch screen operator station
A-B PanelView 10” TouchScreen
(Gray w/ yellow background for easy viewing)
Programmable logic controller
A-B SLC500 PASSWORD protected
Molding speed (nominal)
At maximum height cope & drag,
Excluding CORE insertion time.
Sprue cup & down sprue
One Set: 1 3/16”dia. (30mm)
Sprue positions
Six (6) are Standard/Ten (10) Optional
Six (6) are standard, Ten (10) are OPTIONAL
Top of drag flask with machine on floor (core set ht.)
1900 mm (74.80”)
20 mm ( 0.80”)
1920 mm (75.60”)
850 mm (33.40”)
1070 mm (42.20”)
Pattern maximum weight
Pattern thickness
Thickness: 1" - 1-3/8" (30mm +/- 5mm)
Squeeze pressure:
Maximum 102,250 lbs.
Low 85 PSI, mid 114 PSI, high 142 PSI
Maximum 136,300 lbs.
Low 85 PSI, mid 114 PSI, high142 PSI
Maximum 145,400 lbs.
Sand requirements
Moisture: 3-4% (+/- 0.25% of an avg. value)
Compactability: 36-45%
Green strength: 11-21 PSI (for Iron only)
Total clay: 10-13% max.
Temperature: 20F above ambient max.
Sand quantity per mold / tons-per-hour
Maximum 900 lbs. / (40 - 42 TPH)
Maximum 1,400 lbs. / (56 - 58 TPH)
Maximum 1,350 lbs. / (52 - 54 TPH)
Maximum 1,555 lbs. / (62 - 64 TPH)
Air tank (minimum requirement)
5 cubic meters / 180 cubic feet / 1320 gallons
Utilities (approximate):
Air pressure required
80 +/- 6 PSI
Air quantity per mold
(Per ANSI/CGA G7.1 Specifications - 1989)
Hydraulic Power Unit
(ISO VG46 wear-resistant oil by others )
94 CFFA/mold -- 141 ACFM
145 CFFA/mold – 218 ACFM
135 CFFA/mold -- 202 ACFM
155 CFFA/mold -- 206 ACFM
Water cooled heat exchanger (¾” in, ¾” out)
Line Filters: Return & Cooler continuous flow
Noise level: Less than 75 dB
Required electrical service, minimum
LITERS/GPM required: 250/66
Hydraulic power unit
For: 56 KW/ 75 HP/ 90FLA
USA , Canada , Mexico & South America
Control Voltage: 110 VAC, 1 ph., 60 Hz.
USA
Power Voltage: 480 VAC, 3 ph., 60 Hz.
Canada (CSA)
Power Voltage: 575 VAC, 3 ph., 60 Hz.
Mexico & South America
(voltage regulation transformer)
Dimensions
202.83"w. x 235.24"d. x 214.45"h.
(5152mm x 5975mm x 5447mm)
203"w. x 236"d. x 215"h.
Machine Weight
62,000 lbs (28,180 kg)
